LENZ USB INTERFACE DRIVER DOWNLOAD

So must be holding my mouth wrong again. Thanks for response have done as suggested and no go keeps on reporting no driver found. The XpressNet specification available from the Lenz website specifies the electrical communications standards and command set needed for devices to communicate with the command station. I think I tried the FDTI site earlier on when the laptop was running W7 starter not tried with W7 HP, have downloaded again from the web site and will try again this afternoon. System specific limitations are also expressed in the Limitations section of each system below.

Uploader:	Gazahn
Date Added:	5 June 2011
File Size:	39.21 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	34484
Price:	Free* [*Free Regsitration Required]

David Peters Dr Beeching.

Lenz USB - Interface | eBay

These ports can be used to connect one of the supported XpressNet computer interfaces, but it is unknown at this point what, if any, limitations exist when using this connection. Jun 11, Last Visited: The BlackBox only does programming, and cannot operate either locomotives or accessory decoders turnouts on the layout. Jun 12, Last Visited: The unit features ihterface built in USB port, but it is unknown at this time how we can utilize it.

Thanks for the information. Interace Compact is not available in North America. If you choose to use an XPA and a Hayes Compatible Modem to control your XpressNet based system, you will be limited to control of locomotives and accessory decoders.

The following table tries to show which systems support these three feature groups. If you have installed the Lenz software, make sure none of it is running. I think I tried the FDTI site earlier on when the laptop was running W7 starter not tried jnterface W7 HP, have downloaded again from the web site and will try again this afternoon.

Lenz usb interface (Page 1) / Model Railways / General Discussions / Forums / Railpage

Could the Lenz USB interface be for a slightly older computer system like XP or something, yeah I know it should work, but then again in windows anything can and does happen.

You cannot program decoders from a computer with the Knterface. Windows 7 bit will not, unless you press F8 just when starting up to bring up the options menu.

The BlackBox is a standalone decoder programmer. You can't program decoders from a computer with Set Thanks for response have done as suggested and no go keeps on reporting no driver found. The following tools are available from the XpressNet menu when this connection is active click on the name to read more on each tool:. We have developed an alternative method for connecting to an XpressNet based system which should prove to be more cost effective on XpressNet based systems that do not support programming or feedback via the LI, LIF, or LIF computer interfaces, or for those who are interested in experimenting with computer control, but don't need all the features supported by the Lenz interfaces.

The XpressNet specification available from the Lenz website specifies the electrical communications standards and command set needed for devices to communicate with the command station. Viessmann has indicated the Commander's built in USB port can only be used for updating the firmware and sending data to the commander, not for operating the device.

Lenz Li-USB-Ethernet Computer Interface

Jul 20, Last Visited: Hendo Are well wait for Lenz innterface update the software. Peter, Here is something else from another source The FTDI website has very detailed instructions on installing their drivers for Windows 7, as it appears to be a two-part process: It may be necessary to build an adapter to plug an XpressNet accessory into a Command Station from another manufacturer.

Roco calls their XpressNet implementation "RocoNet". Lenz We have a pretty good handle on what instructions each Lenz Command station should support. Paco Canada also provides two methods for adding feedback to non-feedback equipped systems.

OK downloaded again the files from Tony, above, and transferred to my laptop, which I have now updated to home premium 32 bit.

Stats lez nerds Gen time: The Compact is the same device as the Atlas Commander, and has the same restrictions as the commander. Hardware Limitations Lnterface with: Jan 20, Last Visited: This includes the LI-Server, which may be running in the background. If you have either ZTC system and wish to add computer control to your layout, an XPA and Hayes Compatible Modem may be a more cost effective solution than one of the purpose built interfaces.

You cannot program decoders from a computer using the XPA, regardless of which system you have.